Thermal evolution of the mechanical properties of calcareous earthenware

Autores
Serra, Maria Florencia; Acebedo, Maria Florencia; Conconi, María Susana; Suarez, Gustavo; Aglietti, Esteban Fausto; Rendtorff Birrer, Nicolás Maximiliano
Año de publicación
2014
Idioma
inglés
Tipo de recurso
artículo
Estado
versión publicada
Descripción
Calcareous earthenware is used very frequently for tableware, and fired twice between 980 °C and 1040 °C. Before firing it mostly consists in a kaolinitic clay accompanied by quartz and ≈7 wt% of carbonates (Ca and Mg) as fluxing fraction. In this article the firing temperature correlation with the textural, structural and mechanical properties was established in the 700–1100 °C firing range. Materials fired between 800 and 1050 °C presented an interesting correlation between the processing variable (temperature) and the evaluated properties. The porosity in this range was almost constant however the properties evolved exponentially with the temperature. A parallel behavior between flexural strength, diametral compression resistance and dynamic elastic modulus was observed. Furthermore within the technological temperature range the correlation was linear. Finally the incorporation of the porosimetric analysis performed permitted to understand that the firing processes of calcareous earthenware below 1050 °C is not strictly a sintering process with a gradual densification and loss of porosity: it should be considered as a series of complex chemical processes accompanied by a textural evolution of pore size increase with no important porosity decrease. Only for higher temperature treatments (which exceed the technological ones) the porosity diminishes abruptly. When this reduction takes place, it is accompanied by an increment in the mechanical properties figures and a loss in the dimensional stability.
Fil: Serra, Maria Florencia. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Acebedo, Maria Florencia. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Conconi, María Susana. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Suarez, Gustavo. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina
Fil: Aglietti, Esteban Fausto. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Rendtorff Birrer, Nicolás Maximiliano. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Materia
C. Mechanical Properties
Clay Based Ceramics
Earthenware
Processing
Nivel de accesibilidad
acceso abierto
Condiciones de uso
https://creativecommons.org/licenses/by-nc-sa/2.5/ar/
Repositorio
CONICET Digital (CONICET)
Institución
Consejo Nacional de Investigaciones Científicas y Técnicas
OAI Identificador
oai:ri.conicet.gov.ar:11336/32395
Acceder
id CONICETDig_06134b271cf0ab98740723a273d8de78
oai_identifier_str oai:ri.conicet.gov.ar:11336/32395
network_acronym_str CONICETDig
repository_id_str 3498
network_name_str CONICET Digital (CONICET)
spelling Thermal evolution of the mechanical properties of calcareous earthenwareSerra, Maria FlorenciaAcebedo, Maria FlorenciaConconi, María SusanaSuarez, GustavoAglietti, Esteban FaustoRendtorff Birrer, Nicolás MaximilianoC. Mechanical PropertiesClay Based CeramicsEarthenwareProcessinghttps://purl.org/becyt/ford/2.5https://purl.org/becyt/ford/2Calcareous earthenware is used very frequently for tableware, and fired twice between 980 °C and 1040 °C. Before firing it mostly consists in a kaolinitic clay accompanied by quartz and ≈7 wt% of carbonates (Ca and Mg) as fluxing fraction. In this article the firing temperature correlation with the textural, structural and mechanical properties was established in the 700–1100 °C firing range. Materials fired between 800 and 1050 °C presented an interesting correlation between the processing variable (temperature) and the evaluated properties. The porosity in this range was almost constant however the properties evolved exponentially with the temperature. A parallel behavior between flexural strength, diametral compression resistance and dynamic elastic modulus was observed. Furthermore within the technological temperature range the correlation was linear. Finally the incorporation of the porosimetric analysis performed permitted to understand that the firing processes of calcareous earthenware below 1050 °C is not strictly a sintering process with a gradual densification and loss of porosity: it should be considered as a series of complex chemical processes accompanied by a textural evolution of pore size increase with no important porosity decrease. Only for higher temperature treatments (which exceed the technological ones) the porosity diminishes abruptly. When this reduction takes place, it is accompanied by an increment in the mechanical properties figures and a loss in the dimensional stability.Fil: Serra, Maria Florencia. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; ArgentinaFil: Acebedo, Maria Florencia. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; ArgentinaFil: Conconi, María Susana. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; ArgentinaFil: Suarez, Gustavo. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; ArgentinaFil: Aglietti, Esteban Fausto. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; ArgentinaFil: Rendtorff Birrer, Nicolás Maximiliano. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; ArgentinaElsevier2014-01info:eu-repo/semantics/articleinfo:eu-repo/semantics/publishedVersionhttp://purl.org/coar/resource_type/c_6501info:ar-repo/semantics/articuloapplication/pdfapplication/pdfapplication/pdfapplication/pdfapplication/pdfapplication/pdfhttp://hdl.handle.net/11336/32395Rendtorff Birrer, Nicolás Maximiliano; Aglietti, Esteban Fausto; Suarez, Gustavo; Conconi, María Susana; Acebedo, Maria Florencia; Serra, Maria Florencia; et al.; Thermal evolution of the mechanical properties of calcareous earthenware; Elsevier; Ceramics International; 40; 1B; 1-2014; 1709-17160272-8842CONICET DigitalCONICETenginfo:eu-repo/semantics/altIdentifier/doi/10.1016/j.ceramint.2013.07.067info:eu-repo/semantics/altIdentifier/url/http://www.sciencedirect.com/science/article/pii/S0272884213008614info:eu-repo/semantics/openAccesshttps://creativecommons.org/licenses/by-nc-sa/2.5/ar/reponame:CONICET Digital (CONICET)instname:Consejo Nacional de Investigaciones Científicas y Técnicas2025-10-15T15:05:50Zoai:ri.conicet.gov.ar:11336/32395instacron:CONICETInstitucionalhttp://ri.conicet.gov.ar/Organismo científico-tecnológicoNo correspondehttp://ri.conicet.gov.ar/oai/requestdasensio@conicet.gov.ar; lcarlino@conicet.gov.arArgentinaNo correspondeNo correspondeNo correspondeopendoar:34982025-10-15 15:05:50.459CONICET Digital (CONICET) - Consejo Nacional de Investigaciones Científicas y Técnicasfalse
dc.title.none.fl_str_mv Thermal evolution of the mechanical properties of calcareous earthenware
title Thermal evolution of the mechanical properties of calcareous earthenware
spellingShingle Thermal evolution of the mechanical properties of calcareous earthenware
Serra, Maria Florencia
C. Mechanical Properties
Clay Based Ceramics
Earthenware
Processing
title_short Thermal evolution of the mechanical properties of calcareous earthenware
title_full Thermal evolution of the mechanical properties of calcareous earthenware
title_fullStr Thermal evolution of the mechanical properties of calcareous earthenware
title_full_unstemmed Thermal evolution of the mechanical properties of calcareous earthenware
title_sort Thermal evolution of the mechanical properties of calcareous earthenware
dc.creator.none.fl_str_mv Serra, Maria Florencia
Acebedo, Maria Florencia
Conconi, María Susana
Suarez, Gustavo
Aglietti, Esteban Fausto
Rendtorff Birrer, Nicolás Maximiliano
author Serra, Maria Florencia
author_facet Serra, Maria Florencia
Acebedo, Maria Florencia
Conconi, María Susana
Suarez, Gustavo
Aglietti, Esteban Fausto
Rendtorff Birrer, Nicolás Maximiliano
author_role author
author2 Acebedo, Maria Florencia
Conconi, María Susana
Suarez, Gustavo
Aglietti, Esteban Fausto
Rendtorff Birrer, Nicolás Maximiliano
author2_role author
author
author
author
author
dc.subject.none.fl_str_mv C. Mechanical Properties
Clay Based Ceramics
Earthenware
Processing
topic C. Mechanical Properties
Clay Based Ceramics
Earthenware
Processing
purl_subject.fl_str_mv https://purl.org/becyt/ford/2.5
https://purl.org/becyt/ford/2
dc.description.none.fl_txt_mv Calcareous earthenware is used very frequently for tableware, and fired twice between 980 °C and 1040 °C. Before firing it mostly consists in a kaolinitic clay accompanied by quartz and ≈7 wt% of carbonates (Ca and Mg) as fluxing fraction. In this article the firing temperature correlation with the textural, structural and mechanical properties was established in the 700–1100 °C firing range. Materials fired between 800 and 1050 °C presented an interesting correlation between the processing variable (temperature) and the evaluated properties. The porosity in this range was almost constant however the properties evolved exponentially with the temperature. A parallel behavior between flexural strength, diametral compression resistance and dynamic elastic modulus was observed. Furthermore within the technological temperature range the correlation was linear. Finally the incorporation of the porosimetric analysis performed permitted to understand that the firing processes of calcareous earthenware below 1050 °C is not strictly a sintering process with a gradual densification and loss of porosity: it should be considered as a series of complex chemical processes accompanied by a textural evolution of pore size increase with no important porosity decrease. Only for higher temperature treatments (which exceed the technological ones) the porosity diminishes abruptly. When this reduction takes place, it is accompanied by an increment in the mechanical properties figures and a loss in the dimensional stability.
Fil: Serra, Maria Florencia. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Acebedo, Maria Florencia. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Conconi, María Susana. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Suarez, Gustavo. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina
Fil: Aglietti, Esteban Fausto. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
Fil: Rendtorff Birrer, Nicolás Maximiliano. Universidad Nacional de La Plata. Facultad de Ciencias Exactas. Departamento de Química; Argentina. Provincia de Buenos Aires. Gobernación. Comision de Invest.científicas. Centro de Tecnología de Recursos Minerales y Ceramica. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - la Plata. Centro de Tecnología de Recursos Minerales y Ceramica; Argentina
description Calcareous earthenware is used very frequently for tableware, and fired twice between 980 °C and 1040 °C. Before firing it mostly consists in a kaolinitic clay accompanied by quartz and ≈7 wt% of carbonates (Ca and Mg) as fluxing fraction. In this article the firing temperature correlation with the textural, structural and mechanical properties was established in the 700–1100 °C firing range. Materials fired between 800 and 1050 °C presented an interesting correlation between the processing variable (temperature) and the evaluated properties. The porosity in this range was almost constant however the properties evolved exponentially with the temperature. A parallel behavior between flexural strength, diametral compression resistance and dynamic elastic modulus was observed. Furthermore within the technological temperature range the correlation was linear. Finally the incorporation of the porosimetric analysis performed permitted to understand that the firing processes of calcareous earthenware below 1050 °C is not strictly a sintering process with a gradual densification and loss of porosity: it should be considered as a series of complex chemical processes accompanied by a textural evolution of pore size increase with no important porosity decrease. Only for higher temperature treatments (which exceed the technological ones) the porosity diminishes abruptly. When this reduction takes place, it is accompanied by an increment in the mechanical properties figures and a loss in the dimensional stability.
publishDate 2014
dc.date.none.fl_str_mv 2014-01
dc.type.none.fl_str_mv info:eu-repo/semantics/article
info:eu-repo/semantics/publishedVersion
http://purl.org/coar/resource_type/c_6501
info:ar-repo/semantics/articulo
format article
status_str publishedVersion
dc.identifier.none.fl_str_mv http://hdl.handle.net/11336/32395
Rendtorff Birrer, Nicolás Maximiliano; Aglietti, Esteban Fausto; Suarez, Gustavo; Conconi, María Susana; Acebedo, Maria Florencia; Serra, Maria Florencia; et al.; Thermal evolution of the mechanical properties of calcareous earthenware; Elsevier; Ceramics International; 40; 1B; 1-2014; 1709-1716
0272-8842
CONICET Digital
CONICET
url http://hdl.handle.net/11336/32395
identifier_str_mv Rendtorff Birrer, Nicolás Maximiliano; Aglietti, Esteban Fausto; Suarez, Gustavo; Conconi, María Susana; Acebedo, Maria Florencia; Serra, Maria Florencia; et al.; Thermal evolution of the mechanical properties of calcareous earthenware; Elsevier; Ceramics International; 40; 1B; 1-2014; 1709-1716
0272-8842
CONICET Digital
CONICET
dc.language.none.fl_str_mv eng
language eng
dc.relation.none.fl_str_mv info:eu-repo/semantics/altIdentifier/doi/10.1016/j.ceramint.2013.07.067
info:eu-repo/semantics/altIdentifier/url/http://www.sciencedirect.com/science/article/pii/S0272884213008614
dc.rights.none.fl_str_mv info:eu-repo/semantics/openAccess
https://creativecommons.org/licenses/by-nc-sa/2.5/ar/
eu_rights_str_mv openAccess
rights_invalid_str_mv https://creativecommons.org/licenses/by-nc-sa/2.5/ar/
dc.format.none.fl_str_mv application/pdf
application/pdf
application/pdf
application/pdf
application/pdf
application/pdf
dc.publisher.none.fl_str_mv Elsevier
publisher.none.fl_str_mv Elsevier
dc.source.none.fl_str_mv reponame:CONICET Digital (CONICET)
instname:Consejo Nacional de Investigaciones Científicas y Técnicas
reponame_str CONICET Digital (CONICET)
collection CONICET Digital (CONICET)
instname_str Consejo Nacional de Investigaciones Científicas y Técnicas
repository.name.fl_str_mv CONICET Digital (CONICET) - Consejo Nacional de Investigaciones Científicas y Técnicas
repository.mail.fl_str_mv dasensio@conicet.gov.ar; lcarlino@conicet.gov.ar
_version_ 1846083201122959360
score 13.22299

Publicaciones similares