Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates
- Autores
- de Castro Bubani, Franco; Sade Lichtmann, Marcos Leonel; Lovey, Francisco
- Año de publicación
- 2013
- Idioma
- inglés
- Tipo de recurso
- artículo
- Estado
- versión publicada
- Descripción
- Mechanical damping applications could benefit from the large hysteresis, large pseudoelastic strain and the fact that the transformation stresses of the 18R↔6R martensite–martensite transformation depend very little on temperature in Cu-based alloys. This work presents the 18R↔6R mechanical cycling behavior of CuZnAl shape-memory alloy single crystals with electronic concentration e/a¼1.48. A fine distribution of gamma phase nanoprecipitates is introduced to prevent plastic deformation of the 6R phase. Results show that, although significant 6R stabilization is observed at very low frequencies (below 10−2 Hz), it is possible to obtain more than 1000 stable pseudoelastic cycles with only minor changes in transformation stresses and hysteresis width at frequencies above 10−1 Hz. A more pronounced decrease in transformation stresses is observed after 1000 cycles. Nevertheless, the decrease in hysteresis is small up to 2000 cycles. Reported and present results indicate that pair interchange of atoms can explain the stabilization of 6R under quasistatic experimental conditions. However, at higher frequencies of cycling, stabilization of this martensite shows additional features, leading to a dynamic stabilization with slight effects on the mechanical behavior at the required frequency and number of cycles. On the whole, the behavior of this transformation is unique and very promising.
Fil: de Castro Bubani, Franco. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; Argentina
Fil: Sade Lichtmann, Marcos Leonel. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; Argentina
Fil: Lovey, Francisco. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; Argentina - Materia
-
Shape Memory Alloys
Mechanical Characterization
Martensitic Transformations
Strain Measurement - Nivel de accesibilidad
- acceso abierto
- Condiciones de uso
- https://creativecommons.org/licenses/by-nc-nd/2.5/ar/
- Repositorio
- Institución
- Consejo Nacional de Investigaciones Científicas y Técnicas
- OAI Identificador
- oai:ri.conicet.gov.ar:11336/8978
Ver los metadatos del registro completo
id |
CONICETDig_a0d93e384661510a5aef16e827c1b865 |
---|---|
oai_identifier_str |
oai:ri.conicet.gov.ar:11336/8978 |
network_acronym_str |
CONICETDig |
repository_id_str |
3498 |
network_name_str |
CONICET Digital (CONICET) |
spelling |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitatesde Castro Bubani, FrancoSade Lichtmann, Marcos LeonelLovey, FranciscoShape Memory AlloysMechanical CharacterizationMartensitic TransformationsStrain Measurementhttps://purl.org/becyt/ford/1.3https://purl.org/becyt/ford/1Mechanical damping applications could benefit from the large hysteresis, large pseudoelastic strain and the fact that the transformation stresses of the 18R↔6R martensite–martensite transformation depend very little on temperature in Cu-based alloys. This work presents the 18R↔6R mechanical cycling behavior of CuZnAl shape-memory alloy single crystals with electronic concentration e/a¼1.48. A fine distribution of gamma phase nanoprecipitates is introduced to prevent plastic deformation of the 6R phase. Results show that, although significant 6R stabilization is observed at very low frequencies (below 10−2 Hz), it is possible to obtain more than 1000 stable pseudoelastic cycles with only minor changes in transformation stresses and hysteresis width at frequencies above 10−1 Hz. A more pronounced decrease in transformation stresses is observed after 1000 cycles. Nevertheless, the decrease in hysteresis is small up to 2000 cycles. Reported and present results indicate that pair interchange of atoms can explain the stabilization of 6R under quasistatic experimental conditions. However, at higher frequencies of cycling, stabilization of this martensite shows additional features, leading to a dynamic stabilization with slight effects on the mechanical behavior at the required frequency and number of cycles. On the whole, the behavior of this transformation is unique and very promising.Fil: de Castro Bubani, Franco. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; ArgentinaFil: Sade Lichtmann, Marcos Leonel. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; ArgentinaFil: Lovey, Francisco. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; ArgentinaElsevier Science2013-08info:eu-repo/semantics/articleinfo:eu-repo/semantics/publishedVersionhttp://purl.org/coar/resource_type/c_6501info:ar-repo/semantics/articuloapplication/pdfapplication/pdfapplication/pdfhttp://hdl.handle.net/11336/8978de Castro Bubani, Franco; Sade Lichtmann, Marcos Leonel; Lovey, Francisco; Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates; Elsevier Science; Materials Science And Engineering A: Structural Materials: Properties, Microstructure And Processing; 577; 8-2013; 147-1570921-5093enginfo:eu-repo/semantics/altIdentifier/url/http://www.sciencedirect.com/science/article/pii/S092150931300419Xinfo:eu-repo/semantics/altIdentifier/doi/10.1016/j.msea.2013.04.037info:eu-repo/semantics/openAccesshttps://creativecommons.org/licenses/by-nc-nd/2.5/ar/reponame:CONICET Digital (CONICET)instname:Consejo Nacional de Investigaciones Científicas y Técnicas2025-09-03T10:11:50Zoai:ri.conicet.gov.ar:11336/8978instacron:CONICETInstitucionalhttp://ri.conicet.gov.ar/Organismo científico-tecnológicoNo correspondehttp://ri.conicet.gov.ar/oai/requestdasensio@conicet.gov.ar; lcarlino@conicet.gov.arArgentinaNo correspondeNo correspondeNo correspondeopendoar:34982025-09-03 10:11:51.129CONICET Digital (CONICET) - Consejo Nacional de Investigaciones Científicas y Técnicasfalse |
dc.title.none.fl_str_mv |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
title |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
spellingShingle |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates de Castro Bubani, Franco Shape Memory Alloys Mechanical Characterization Martensitic Transformations Strain Measurement |
title_short |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
title_full |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
title_fullStr |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
title_full_unstemmed |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
title_sort |
Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates |
dc.creator.none.fl_str_mv |
de Castro Bubani, Franco Sade Lichtmann, Marcos Leonel Lovey, Francisco |
author |
de Castro Bubani, Franco |
author_facet |
de Castro Bubani, Franco Sade Lichtmann, Marcos Leonel Lovey, Francisco |
author_role |
author |
author2 |
Sade Lichtmann, Marcos Leonel Lovey, Francisco |
author2_role |
author author |
dc.subject.none.fl_str_mv |
Shape Memory Alloys Mechanical Characterization Martensitic Transformations Strain Measurement |
topic |
Shape Memory Alloys Mechanical Characterization Martensitic Transformations Strain Measurement |
purl_subject.fl_str_mv |
https://purl.org/becyt/ford/1.3 https://purl.org/becyt/ford/1 |
dc.description.none.fl_txt_mv |
Mechanical damping applications could benefit from the large hysteresis, large pseudoelastic strain and the fact that the transformation stresses of the 18R↔6R martensite–martensite transformation depend very little on temperature in Cu-based alloys. This work presents the 18R↔6R mechanical cycling behavior of CuZnAl shape-memory alloy single crystals with electronic concentration e/a¼1.48. A fine distribution of gamma phase nanoprecipitates is introduced to prevent plastic deformation of the 6R phase. Results show that, although significant 6R stabilization is observed at very low frequencies (below 10−2 Hz), it is possible to obtain more than 1000 stable pseudoelastic cycles with only minor changes in transformation stresses and hysteresis width at frequencies above 10−1 Hz. A more pronounced decrease in transformation stresses is observed after 1000 cycles. Nevertheless, the decrease in hysteresis is small up to 2000 cycles. Reported and present results indicate that pair interchange of atoms can explain the stabilization of 6R under quasistatic experimental conditions. However, at higher frequencies of cycling, stabilization of this martensite shows additional features, leading to a dynamic stabilization with slight effects on the mechanical behavior at the required frequency and number of cycles. On the whole, the behavior of this transformation is unique and very promising. Fil: de Castro Bubani, Franco. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; Argentina Fil: Sade Lichtmann, Marcos Leonel. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; Argentina Fil: Lovey, Francisco. Comision Nacional de Energia Atomica. Gerencia del Area de Investigaciones y Aplicaciones no Nucleares. Gerencia de Fisica (CAB); Argentina. Comisión Nacional de Energía Atómica. Gerencia del Area de Energía Nuclear. Instituto Balseiro; Argentina |
description |
Mechanical damping applications could benefit from the large hysteresis, large pseudoelastic strain and the fact that the transformation stresses of the 18R↔6R martensite–martensite transformation depend very little on temperature in Cu-based alloys. This work presents the 18R↔6R mechanical cycling behavior of CuZnAl shape-memory alloy single crystals with electronic concentration e/a¼1.48. A fine distribution of gamma phase nanoprecipitates is introduced to prevent plastic deformation of the 6R phase. Results show that, although significant 6R stabilization is observed at very low frequencies (below 10−2 Hz), it is possible to obtain more than 1000 stable pseudoelastic cycles with only minor changes in transformation stresses and hysteresis width at frequencies above 10−1 Hz. A more pronounced decrease in transformation stresses is observed after 1000 cycles. Nevertheless, the decrease in hysteresis is small up to 2000 cycles. Reported and present results indicate that pair interchange of atoms can explain the stabilization of 6R under quasistatic experimental conditions. However, at higher frequencies of cycling, stabilization of this martensite shows additional features, leading to a dynamic stabilization with slight effects on the mechanical behavior at the required frequency and number of cycles. On the whole, the behavior of this transformation is unique and very promising. |
publishDate |
2013 |
dc.date.none.fl_str_mv |
2013-08 |
dc.type.none.fl_str_mv |
info:eu-repo/semantics/article info:eu-repo/semantics/publishedVersion http://purl.org/coar/resource_type/c_6501 info:ar-repo/semantics/articulo |
format |
article |
status_str |
publishedVersion |
dc.identifier.none.fl_str_mv |
http://hdl.handle.net/11336/8978 de Castro Bubani, Franco; Sade Lichtmann, Marcos Leonel; Lovey, Francisco; Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates; Elsevier Science; Materials Science And Engineering A: Structural Materials: Properties, Microstructure And Processing; 577; 8-2013; 147-157 0921-5093 |
url |
http://hdl.handle.net/11336/8978 |
identifier_str_mv |
de Castro Bubani, Franco; Sade Lichtmann, Marcos Leonel; Lovey, Francisco; Mechanical Behavior Under Cyclic Loading of the 18R-6R High-hysteresis Martensitic Transformation in Cu-Zn-Al alloys with Nanoprecipitates; Elsevier Science; Materials Science And Engineering A: Structural Materials: Properties, Microstructure And Processing; 577; 8-2013; 147-157 0921-5093 |
dc.language.none.fl_str_mv |
eng |
language |
eng |
dc.relation.none.fl_str_mv |
info:eu-repo/semantics/altIdentifier/url/http://www.sciencedirect.com/science/article/pii/S092150931300419X info:eu-repo/semantics/altIdentifier/doi/10.1016/j.msea.2013.04.037 |
dc.rights.none.fl_str_mv |
info:eu-repo/semantics/openAccess https://creativecommons.org/licenses/by-nc-nd/2.5/ar/ |
eu_rights_str_mv |
openAccess |
rights_invalid_str_mv |
https://creativecommons.org/licenses/by-nc-nd/2.5/ar/ |
dc.format.none.fl_str_mv |
application/pdf application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Elsevier Science |
publisher.none.fl_str_mv |
Elsevier Science |
dc.source.none.fl_str_mv |
reponame:CONICET Digital (CONICET) instname:Consejo Nacional de Investigaciones Científicas y Técnicas |
reponame_str |
CONICET Digital (CONICET) |
collection |
CONICET Digital (CONICET) |
instname_str |
Consejo Nacional de Investigaciones Científicas y Técnicas |
repository.name.fl_str_mv |
CONICET Digital (CONICET) - Consejo Nacional de Investigaciones Científicas y Técnicas |
repository.mail.fl_str_mv |
dasensio@conicet.gov.ar; lcarlino@conicet.gov.ar |
_version_ |
1842270172916744192 |
score |
13.13397 |