Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers

Autores
Mansilla, Marcela Angela; Rodriguez Garraza, Ana Lucia; Silva, Leonel Ignacio; Salgueiro, Walter Alberto; Macchi, Carlos Eugenio; Marzocca, Angel José; Somoza, Alberto Horacio
Año de publicación
2013
Idioma
inglés
Tipo de recurso
artículo
Estado
versión publicada
Descripción
An investigation of the influence of the cure time on the glass transition temperature and nanostructure for two isomers of polybutadiene rubbers, CB25 (97% cis) and CB55 (38% cis), vulcanized at 433 K is presented. The samples were prepared with sulphur and TBBS (N-tbutyl- 2-benzothiazole sulfenamide), and several crosslink densities were achieved at the different selected cure times. The studies on the samples were carried out using differential scanning calorimetry and positron annihilation lifetime spectroscopy. The variation of the glass transition temperature with the degree of cure and its relation with the crosslink density is analyzed for each type of isomer. A correlation between the free nanohole volume and the crosslink density is also analyzed. From swelling tests, the absorbed solvent at room temperature is discussed in terms of the obtained free nanohole volumes, showing a correspondence between these parameters. In the frame of the obtained results, the cis to trans isomerisation of the elastomer with high cis content during the vulcanization is discussed.
Fil: Mansilla, Marcela Angela. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina
Fil: Rodriguez Garraza, Ana Lucia. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina
Fil: Silva, Leonel Ignacio. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina
Fil: Salgueiro, Walter Alberto. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina. Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas; Argentina. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina
Fil: Macchi, Carlos Eugenio. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina
Fil: Marzocca, Angel José. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina
Fil: Somoza, Alberto Horacio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas; Argentina
Materia
FREE VOLUME
GLASS TRANSITION
PALS
POLYBUTADIENE RUBBER
VULCANIZATION
Nivel de accesibilidad
acceso abierto
Condiciones de uso
https://creativecommons.org/licenses/by-nc-nd/2.5/ar/
Repositorio
CONICET Digital (CONICET)
Institución
Consejo Nacional de Investigaciones Científicas y Técnicas
OAI Identificador
oai:ri.conicet.gov.ar:11336/2225

id CONICETDig_7f1d17f2f1b3e61dabfb044f42484426
oai_identifier_str oai:ri.conicet.gov.ar:11336/2225
network_acronym_str CONICETDig
repository_id_str 3498
network_name_str CONICET Digital (CONICET)
spelling Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbersMansilla, Marcela AngelaRodriguez Garraza, Ana LuciaSilva, Leonel IgnacioSalgueiro, Walter AlbertoMacchi, Carlos EugenioMarzocca, Angel JoséSomoza, Alberto HoracioFREE VOLUMEGLASS TRANSITIONPALSPOLYBUTADIENE RUBBERVULCANIZATIONhttps://purl.org/becyt/ford/1.3https://purl.org/becyt/ford/1An investigation of the influence of the cure time on the glass transition temperature and nanostructure for two isomers of polybutadiene rubbers, CB25 (97% cis) and CB55 (38% cis), vulcanized at 433 K is presented. The samples were prepared with sulphur and TBBS (N-tbutyl- 2-benzothiazole sulfenamide), and several crosslink densities were achieved at the different selected cure times. The studies on the samples were carried out using differential scanning calorimetry and positron annihilation lifetime spectroscopy. The variation of the glass transition temperature with the degree of cure and its relation with the crosslink density is analyzed for each type of isomer. A correlation between the free nanohole volume and the crosslink density is also analyzed. From swelling tests, the absorbed solvent at room temperature is discussed in terms of the obtained free nanohole volumes, showing a correspondence between these parameters. In the frame of the obtained results, the cis to trans isomerisation of the elastomer with high cis content during the vulcanization is discussed.Fil: Mansilla, Marcela Angela. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; ArgentinaFil: Rodriguez Garraza, Ana Lucia. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; ArgentinaFil: Silva, Leonel Ignacio. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; ArgentinaFil: Salgueiro, Walter Alberto. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina. Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas; Argentina. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; ArgentinaFil: Macchi, Carlos Eugenio. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; ArgentinaFil: Marzocca, Angel José. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; ArgentinaFil: Somoza, Alberto Horacio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas; ArgentinaElsevier2013-06info:eu-repo/semantics/articleinfo:eu-repo/semantics/publishedVersionhttp://purl.org/coar/resource_type/c_6501info:ar-repo/semantics/articuloapplication/pdfapplication/pdfhttp://hdl.handle.net/11336/2225Mansilla, Marcela Angela; Rodriguez Garraza, Ana Lucia; Silva, Leonel Ignacio; Salgueiro, Walter Alberto; Macchi, Carlos Eugenio; et al.; Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers; Elsevier; Polymer Testing; 32; 4; 6-2013; 686-6900142-9418enginfo:eu-repo/semantics/altIdentifier/doi/10.1016/j.polymertesting.2013.03.001info:eu-repo/semantics/altIdentifier/url/http://www.sciencedirect.com/science/article/pii/S014294181300041Xinfo:eu-repo/semantics/openAccesshttps://creativecommons.org/licenses/by-nc-nd/2.5/ar/reponame:CONICET Digital (CONICET)instname:Consejo Nacional de Investigaciones Científicas y Técnicas2025-09-29T10:22:28Zoai:ri.conicet.gov.ar:11336/2225instacron:CONICETInstitucionalhttp://ri.conicet.gov.ar/Organismo científico-tecnológicoNo correspondehttp://ri.conicet.gov.ar/oai/requestdasensio@conicet.gov.ar; lcarlino@conicet.gov.arArgentinaNo correspondeNo correspondeNo correspondeopendoar:34982025-09-29 10:22:28.923CONICET Digital (CONICET) - Consejo Nacional de Investigaciones Científicas y Técnicasfalse
dc.title.none.fl_str_mv Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
title Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
spellingShingle Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
Mansilla, Marcela Angela
FREE VOLUME
GLASS TRANSITION
PALS
POLYBUTADIENE RUBBER
VULCANIZATION
title_short Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
title_full Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
title_fullStr Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
title_full_unstemmed Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
title_sort Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
dc.creator.none.fl_str_mv Mansilla, Marcela Angela
Rodriguez Garraza, Ana Lucia
Silva, Leonel Ignacio
Salgueiro, Walter Alberto
Macchi, Carlos Eugenio
Marzocca, Angel José
Somoza, Alberto Horacio
author Mansilla, Marcela Angela
author_facet Mansilla, Marcela Angela
Rodriguez Garraza, Ana Lucia
Silva, Leonel Ignacio
Salgueiro, Walter Alberto
Macchi, Carlos Eugenio
Marzocca, Angel José
Somoza, Alberto Horacio
author_role author
author2 Rodriguez Garraza, Ana Lucia
Silva, Leonel Ignacio
Salgueiro, Walter Alberto
Macchi, Carlos Eugenio
Marzocca, Angel José
Somoza, Alberto Horacio
author2_role author
author
author
author
author
author
dc.subject.none.fl_str_mv FREE VOLUME
GLASS TRANSITION
PALS
POLYBUTADIENE RUBBER
VULCANIZATION
topic FREE VOLUME
GLASS TRANSITION
PALS
POLYBUTADIENE RUBBER
VULCANIZATION
purl_subject.fl_str_mv https://purl.org/becyt/ford/1.3
https://purl.org/becyt/ford/1
dc.description.none.fl_txt_mv An investigation of the influence of the cure time on the glass transition temperature and nanostructure for two isomers of polybutadiene rubbers, CB25 (97% cis) and CB55 (38% cis), vulcanized at 433 K is presented. The samples were prepared with sulphur and TBBS (N-tbutyl- 2-benzothiazole sulfenamide), and several crosslink densities were achieved at the different selected cure times. The studies on the samples were carried out using differential scanning calorimetry and positron annihilation lifetime spectroscopy. The variation of the glass transition temperature with the degree of cure and its relation with the crosslink density is analyzed for each type of isomer. A correlation between the free nanohole volume and the crosslink density is also analyzed. From swelling tests, the absorbed solvent at room temperature is discussed in terms of the obtained free nanohole volumes, showing a correspondence between these parameters. In the frame of the obtained results, the cis to trans isomerisation of the elastomer with high cis content during the vulcanization is discussed.
Fil: Mansilla, Marcela Angela. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina
Fil: Rodriguez Garraza, Ana Lucia. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina
Fil: Silva, Leonel Ignacio. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina
Fil: Salgueiro, Walter Alberto. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina. Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas; Argentina. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina
Fil: Macchi, Carlos Eugenio. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina
Fil: Marzocca, Angel José. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Física. Laboratorio de Polímeros y Materiales Compuestos; Argentina
Fil: Somoza, Alberto Horacio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina. Universidad Nacional del Centro de la Provincia de Buenos Aires. Facultad de Ciencias Exactas. Instituto de Fisica de Materiales; Argentina. Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas; Argentina
description An investigation of the influence of the cure time on the glass transition temperature and nanostructure for two isomers of polybutadiene rubbers, CB25 (97% cis) and CB55 (38% cis), vulcanized at 433 K is presented. The samples were prepared with sulphur and TBBS (N-tbutyl- 2-benzothiazole sulfenamide), and several crosslink densities were achieved at the different selected cure times. The studies on the samples were carried out using differential scanning calorimetry and positron annihilation lifetime spectroscopy. The variation of the glass transition temperature with the degree of cure and its relation with the crosslink density is analyzed for each type of isomer. A correlation between the free nanohole volume and the crosslink density is also analyzed. From swelling tests, the absorbed solvent at room temperature is discussed in terms of the obtained free nanohole volumes, showing a correspondence between these parameters. In the frame of the obtained results, the cis to trans isomerisation of the elastomer with high cis content during the vulcanization is discussed.
publishDate 2013
dc.date.none.fl_str_mv 2013-06
dc.type.none.fl_str_mv info:eu-repo/semantics/article
info:eu-repo/semantics/publishedVersion
http://purl.org/coar/resource_type/c_6501
info:ar-repo/semantics/articulo
format article
status_str publishedVersion
dc.identifier.none.fl_str_mv http://hdl.handle.net/11336/2225
Mansilla, Marcela Angela; Rodriguez Garraza, Ana Lucia; Silva, Leonel Ignacio; Salgueiro, Walter Alberto; Macchi, Carlos Eugenio; et al.; Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers; Elsevier; Polymer Testing; 32; 4; 6-2013; 686-690
0142-9418
url http://hdl.handle.net/11336/2225
identifier_str_mv Mansilla, Marcela Angela; Rodriguez Garraza, Ana Lucia; Silva, Leonel Ignacio; Salgueiro, Walter Alberto; Macchi, Carlos Eugenio; et al.; Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers; Elsevier; Polymer Testing; 32; 4; 6-2013; 686-690
0142-9418
dc.language.none.fl_str_mv eng
language eng
dc.relation.none.fl_str_mv info:eu-repo/semantics/altIdentifier/doi/10.1016/j.polymertesting.2013.03.001
info:eu-repo/semantics/altIdentifier/url/http://www.sciencedirect.com/science/article/pii/S014294181300041X
dc.rights.none.fl_str_mv info:eu-repo/semantics/openAccess
https://creativecommons.org/licenses/by-nc-nd/2.5/ar/
eu_rights_str_mv openAccess
rights_invalid_str_mv https://creativecommons.org/licenses/by-nc-nd/2.5/ar/
dc.format.none.fl_str_mv application/pdf
application/pdf
dc.publisher.none.fl_str_mv Elsevier
publisher.none.fl_str_mv Elsevier
dc.source.none.fl_str_mv reponame:CONICET Digital (CONICET)
instname:Consejo Nacional de Investigaciones Científicas y Técnicas
reponame_str CONICET Digital (CONICET)
collection CONICET Digital (CONICET)
instname_str Consejo Nacional de Investigaciones Científicas y Técnicas
repository.name.fl_str_mv CONICET Digital (CONICET) - Consejo Nacional de Investigaciones Científicas y Técnicas
repository.mail.fl_str_mv dasensio@conicet.gov.ar; lcarlino@conicet.gov.ar
_version_ 1844614216305082368
score 13.070432